Name: Kwantyfikacja danych fluorescencji rentgenowskiej za pomocą MAPS (Wideo) | JoVE Journal
Uploaded: 2018-02-17T12:30:00.000+00:00
Duration: 14 min 58 s
Description: Poznaj metodę kwantyfikacji danych fluorescencji rentgenowskiej za pomocą oprogramowania MAPS. Technika ta umożliwia analizę rozkładu pierwiastków i stosunków stechiometrycznych w próbkach biologicznych i materiałowych.

ai_agent_IP

ai_agent

maintenance

instantTrialDurationMinutes

isBiopharma

enableNewMyJoveSectionDesign

educationFeatures

seoMetaApi

ai_copilot_institution_blacklist

ai_chat_institution_blacklist

freeAccessWindow

ssoRoleCapture

scheduledMaintenanceBanner

joveLabsFeatures

disable_autoplay_for_bots

extended_trial_duration

5 minutes

playerTrialDesktop

We acknowledge funding from the U.S. Department of Energy under contract DE-EE0005948. Use of the Center for Nanoscale Materials and the Advanced Photon Source, both Office of Science user facilities, was supported by the U.S. Department of Energy, Office of Science, Office of Basic Energy Sciences, under Contract No. DE-AC02-06CH11357. This material is based upon work supported in part by the National Science Foundation (NSF) and the Department of Energy (DOE) under NSF CA No. EEC-1041895. Video editing was done by VISLAB at Arizona State University. Any opinions, findings and conclusions or recommendations expressed in this material are those of the author(s) and do not necessarily reflect those of NSF or DOE. T.N. is supported by an IGERT-SUN fellowship funded by the National Science Foundation (Award 1144616).

<ol><li>Geraki, K., Farquharson, M. J., Bradley, D. A. <a target="_blank" href="http://www.ncbi.nlm.nih.gov/pubmed?term=((X-ray+fluorescence+and+energy+dispersive+x-ray+diffraction+for+the+quantification+of+elemental+concentrations+in+breast+tissue%5BTitle%5D)+AND+%22Phys.+Med.+Biol%22%5BJournal%5D)">X-ray fluorescence and energy dispersive x-ray diffraction for the quantification of elemental concentrations in breast tissue.</a> Phys. Med. Biol. 49, 99-110 (2004).</li>
<li>Paunesku, T., Vogt, S., Maser, J., Lai, B., Woloschak, G. <a target="_blank" href="http://www.ncbi.nlm.nih.gov/pubmed?term=((X-ray+fluorescence+microprobe+imaging+in+biology+and+medicine%5BTitle%5D)+AND+%22J.+Cell.+Biochem%22%5BJournal%5D)">X-ray fluorescence microprobe imaging in biology and medicine.</a> J. Cell. Biochem. 99 (6), 1489-1502 (2006).</li>
<li>Twining, B. S., et al. <a target="_blank" href="http://www.ncbi.nlm.nih.gov/pubmed?term=((Quantifying+Trace+Elements+in+Individual+Aquatic+Protist+Cells+with+a+Synchrotron+X-ray+Fluorescence+Microprobe%5BTitle%5D)+AND+%22Anal.+Chem%22%5BJournal%5D)">Quantifying Trace Elements in Individual Aquatic Protist Cells with a Synchrotron X-ray Fluorescence Microprobe.</a> Anal. Chem. 75 (15), 3806-3816 (2003).</li>
<li>de Jonge, M. D., et al. <a target="_blank" href="http://www.ncbi.nlm.nih.gov/pubmed?term=((Quantitative+3D+elemental+microtomography+of+Cylotella+meneghiniana+at+400-nm+resolution%5BTitle%5D)+AND+%22Proc.+Natl.+Acad.+Sci%22%5BJournal%5D)">Quantitative 3D elemental microtomography of Cylotella meneghiniana at 400-nm resolution.</a> Proc. Natl. Acad. Sci. 107 (36), 15676-15680 (2010).</li>
<li>Duĉić, T., et al. <a target="_blank" href="http://www.ncbi.nlm.nih.gov/pubmed?term=((Enhancement+in+statistical+and+image+analysis+for+in+situ+%C2%B5SXRF+studies+of+elemental+distribution+and+co-localization%2C+using+Dioscorea+balcanica%5BTitle%5D)+AND+%22J.+Synchrotron+Rad%22%5BJournal%5D)">Enhancement in statistical and image analysis for in situ µSXRF studies of elemental distribution and co-localization, using Dioscorea balcanica.</a> J. Synchrotron Rad. 20, 339-346 (2013).</li>
<li>Kemner, K. M., et al. <a target="_blank" href="http://www.ncbi.nlm.nih.gov/pubmed?term=((Elemental+and+Redox+Analysis+of+Single+Bacterial+Cells+by+X-ray+Microbeam+Analysis%5BTitle%5D)+AND+%22Science%22%5BJournal%5D)">Elemental and Redox Analysis of Single Bacterial Cells by X-ray Microbeam Analysis.</a> Science. 306 (5696), 686-687 (2004).</li>
<li>Bertoni, M. I., et al. <a target="_blank" href="http://pubs.rsc.org/en/content/articlelanding/2011/ee/c1ee02083h/unauth#!divAbstract">Nanoprobe X-ray fluorescence characterization of defects in large-area solar cells.</a> Energy Environ. Sci. 4 (10), 4252-4257 (2011).</li>
<li>Fenning, D. P., et al. <a target="_blank" href="http://aip.scitation.org/doi/abs/10.1063/1.3575583?journalCode=apl">Iron distribution in silicon after solar cell processing: Synchrotron analysis and predictive modeling.</a> Appl. Phys. Lett. 98 (162103), (2011).</li>
<li>Buonassisi, T., et al. <a target="_blank" href="http://aip.scitation.org/doi/abs/10.1063/1.1997274">Quantifying the effect of metal-rich precipitates on minority carrier diffusion length in multicrystalline silicon using synchrotron-based spectrally resolved x-ray beam induced current.</a> Appl. Phys. Lett. 87 (044101), (2005).</li>
<li>Stuckelberger, M. <a target="_blank" href="https://www.cambridge.org/core/journals/journal-of-materials-research/article/engineering-solar-cells-based-on-correlative-xray-microscopy/92322302DC0E494903FC457912ACE9A3">Engineering solar cells based on correlative X-ray microscopy.</a> J. Mat. Res. 32 (10), 1825-1854 (2017).</li>
<li>Streeck, C., et al. <a target="_blank" href="http://aip.scitation.org/doi/abs/10.1063/1.4821267?journalCode=apl">Grazing-incidence x-ray fluorescence analysis for non-destructive determination of In and Ga depth profiles in Cu(In,Ga)Se2 absorber films.</a> Appl. Phys. Lett. 103 (113904), (2013).</li>
<li>Luo, Y., et al. <a target="_blank" href="http://pubs.acs.org/doi/abs/10.1021/acs.chemmater.6b02065">Spatially Heterogeneous Chlorine Incorporation in Organic-Inorganic Perovskite Solar Cells.</a> Chem. Mater. 28, 6536-6543 (2016).</li>
<li>Stuckelberger, M. <a target="_blank" href="http://ieeexplore.ieee.org/abstract/document/7790832/">Charge Collection in Hybrid Perovskite Solar Cells: Relation to the Nanoscale Elemental Distribution.</a> IEEE J. Photovolt. 7 (2), 590-597 (2017).</li>
<li>Vogt, S., Maser, J., Jacobsen, C. <a target="_blank" href="http://www.ncbi.nlm.nih.gov/pubmed?term=((Data+analysis+for+X-ray+fluorescence+imaging%5BTitle%5D)+AND+%22J.+Phys.+IV+France%22%5BJournal%5D)">Data analysis for X-ray fluorescence imaging.</a> J. Phys. IV France. 104, 617-622 (2003).</li>
<li>Applied X-ray Optics: AXO Dresden. , Available from: 
 <a target="_blank" href="http://axo-dresden.de/mainframe_products.htm">http://axo-dresden.de/mainframe_products.htm</a> (2017).</li>
<li>West, B. M. <a target="_blank" href="http://www.sciencedirect.com/science/article/pii/S2211285516305754">Grain engineering: How nanoscale inhomogeneities can control charge collection in solar cells.</a> Nano Energy. 32, 488-493 (2017).</li>
<li>Krause, M. O. <a target="_blank" href="http://aip.scitation.org/doi/abs/10.1063/1.555594">Atomic Radiative and Radiationless Yields for K and L Shells.</a> J. Phys. Chem. Ref. Data. 8 (2), 307-327 (1979).</li>
<li>Hubbell, J. H., et al. <a target="_blank" href="http://aip.scitation.org/doi/abs/10.1063/1.555955">A Review, Bibliography, and Tabulation of K,L, and Higher Atomic Shell X-Ray Fluorescence Yields.</a> J. Phys. Chem. Ref. Data. 23 (2), 339-364 (1994).</li>
<li>Ravel, B., Newville, M. <a target="_blank" href="http://www.ncbi.nlm.nih.gov/pubmed?term=((ATHENA%2C+ARTEMIS%2C+HEPHAESTUS%3A+data+analysis+for+X-ray+absorption+spectroscopy+using+IFEFFIT%5BTitle%5D)+AND+%22J.+Synchrotron+Rad%22%5BJournal%5D)">ATHENA, ARTEMIS, HEPHAESTUS: data analysis for X-ray absorption spectroscopy using IFEFFIT.</a> J. Synchrotron Rad. 12, 537-541 (2005).</li>
<li>West, B. M., et al. <a target="_blank" href="http://www.ncbi.nlm.nih.gov/pubmed?term=((X-ray+fluorescence+at+nanoscale+resolution+for+multicomponent+layered+structures%3A+a+solar+cell+case+study%5BTitle%5D)+AND+%22J+Synchrotron+Rad%22%5BJournal%5D)">X-ray fluorescence at nanoscale resolution for multicomponent layered structures: a solar cell case study.</a> J Synchrotron Rad. 24, (2017).</li>
<li>De Boer, D. K. G. <a target="_blank" href="http://onlinelibrary.wiley.com/doi/10.1002/xrs.1300190312/abstract">Calculation of X-Ray Fluorescence Intensities from Bulk and Multilayer Samples.</a> X-Ray Spectrom. 19 (3), 145-154 (1990).</li>
<li>Lachance, G. R., Claisse, F. <a target="_blank" href="http://scholar.google.com/scholar?hl=en&safe=off&q=author%3aLachance%2C+GR+%22Quantitative+X-ray+Fluorescence+Analysis%3A+Theory+and+Application%22">Quantitative X-ray Fluorescence Analysis: Theory and Application</a>. , John Wiley & Sons. (1995).</li>
<li>Sokaras, D., Karydas, A. G. <a target="_blank" href="http://www.ncbi.nlm.nih.gov/pubmed?term=((Secondary+Fluorescence+Enhancement+in+Confocal+X-ray+Microscopy+Analysis%5BTitle%5D)+AND+%22Anal.+Chem%22%5BJournal%5D)">Secondary Fluorescence Enhancement in Confocal X-ray Microscopy Analysis.</a> Anal. Chem. 81 (12), 4946-4954 (2009).</li>
</ol>

The authors have nothing to disclose.

The figures show the importance of fitting data using this procedure. Figures 1 (right) and 2 (bottom) show a representative result that should arise from a proper fitting. If there is an insufficient fit, the integral spectrum image will look noticeably off and the resulting quantified data will have errors in it, although these will be hard to detect in most cases. For certain sample types for which the standard is not representative of the elements in the sample, particularly in that the samples do no...

Synchrotron-based XRF has been used across multiple disciplines for many decades. For example, it has been used in biology on studies such as that done by Geraki et al., in which they quantified trace amounts of metal concentrations within cancerous and non-cancerous breast tissue 1. More generally, quantitative XRF has been applied to a wide array of biology studies concerned with metal concentrations in cells and tissues, as described by Paunesku et al.2. Similarly, marine protists were studied for trace elements 3,4 and even micro- and macronutrient distributions were observed within plant cells 5. Work by Kemner et al.6, which identified distinct differences in morphology and elemental composition in single bacteria cells, was also made possible through quantitative XRF analysis. Additionally, and specifically relevant to the example disclosed herein, materials scientists studying solar cell devices have made use of high-resolution XRF for studies on the existence of sub-micron metal impurities in silicon semiconductors 7,8, correlative work on how elemental distributions affect electrical performance in solar devices 9,10, and identifying depth-dependent gradients of CIGS thin film solar cells via grazing incidence X-ray fluorescence (GIXRF) 11.
Many of these studies make use not only of the high-resolution capabilities of synchrotron X-ray fluorescence to study spatial distribution, but also the quantification of the information for drawing numerical conclusions. In many studies it is critical to know the elemental concentrations associated with the aforementioned spatial distributions. For instance, in the work by Geraki et al., the study required quantifying the difference in concentrations of iron, copper, zinc, and potassium in cancerous and non-cancerous breast tissues, to better understand what concentrations become harmful to human tissues 1. Similarly, work by Luo et al. made use of quantified XRF to identify small amounts of chlorine incorporated in perovskite solar cells when synthesized both with and without chlorine-containing precursors 12. Therefore, for certain studies in which the concentrations of elements are needed, proper quantification is a necessary and critical step.
The process of quantifying elemental concentrations from X-ray fluorescence (XRF) measurements translates fluorescence intensity counts into mass concentrations (e.g. &#181;g/cm2). The raw spectra present the number of photons collected by the energy dispersive fluorescence detector as a function of energy. The spectra are first fit and then compared to a standard measurement to calculate the quantified data. In particular, the first step of fitting fluorescence spectra is critical even for the qualitative analysis of the elements. This is because prior to fitting, counts are binned based on their energy, which becomes a problem when two elements with similar fluorescence transitions are contained in the sample. In this situation, counts may be incorrectly binned and thus associated with the wrong element.
It is often also necessary to quantify XRF spectra in order to accurately draw conclusions on relative quantities of elements in a sample. Without proper quantification, counts of heavy elements and lighter elements will be compared directly, ignoring differences in capture cross section, absorption and fluorescence probability, attenuation of the fluorescence photons, and the distance of the element&#39;s absorption edge from the incident energy, which all affect the number of photons striking the detector. Therefore, the process of fitting the spectra for each map and comparing peak intensities to the standard, both of which are done in the following procedure, is critical for the accurate quantification of each of the elemental concentrations.
We demonstrate how to convert the raw counts of fluorescence photons to units of micrograms per square centimeter (&#181;g/cm2) by first fitting an integral spectrum, or a summed spectrum of all the individual spectra produced at each measurement spot or pixel in a 2D map. This spectrum demonstrates the relative intensities of the different elements contained in the sample. The distance the absorption edge of a certain element is from the incident beam energy influences the intensities of their fluorescence peaks. In general, the closer the two energies are, the greater the intensity produced for those elements, although this is not always the case. Figure 4 in Ref 13 shows the dependence of the absorption length of X-ray photons, which directly relates to the resulting intensity, for the majority elements in a methylammonium lead iodide perovskite solar cell. This demonstrates the fluorescence response of elements with respect to energy, and shows that it is not a continual decrease in response with increasing distance from the incident energy, but rather that it is also dependent upon the element itself.
The result of this relationship is that raw elemental concentrations may appear higher for element channels with excitation energies closer to the incident energy, even if the true quantities of those elements are lower in relation to other elements with excitation energies farther from the incident. Therefore, the energy dependence of intensity, along with other factors such as fluorescence yield variations, different absorption edges, detector sensitivity, and measurement background, etc., is why fitting the data is very important prior to drawing conclusions on the observed elemental quantities. We then apply a fitting algorithm to the integral spectrum, where the user defines the elements and parameters to fit via a text document.
The algorithm, created by Vogt et al. 14, makes use of regions of interest (ROI) filtering, in which it integrates over certain elements&#39; peak regions, and principle component analysis (PCA). First, PCA is done to identify only the elements and peaks that are very strongly apparent. This allows for the separation of noise from the true signal. Next, the principle components identified are numerically quantified, which is important for deconvoluting different element peaks with the same excitation energy, for example overlapping Au M&#945; and P K&#945;. Finally, ROI filtering may be applied to the numeric data by integrating over specified regions.
To relate counts to elemental concentrations, a well-quantified reference (often referred to as &#34;standard&#34;) is measured under the same measurement conditions, geometry and energy, as the sample under study. This standard is often from Dresden AXO or from the National Institute of Standards and Technology (NIST). They cover a variety of different elements and come with tabulated elemental distributions. The normalization of the measured counts of the sample of interest to the counts of the standard under the same measurement conditions provides the basis for the elemental quantification for the sample of interest.
More specifically, MAPS identifies the elements and their concentrations of the standard either by the fact that the standard information is known by the program (as is the case for the AXO and NIST standards) or through data entered into a separate file (in the case of a different standard being used). From this information, the program relates the measured intensities of the standard elements under the measurement settings to the anticipated concentration embedded in MAPS. It then creates a scaling factor to adjust for any offset and extrapolates this scaling factor to all the remaining elements not included in the standard. The scaling factor then includes the offset from the measurement settings and the information provided within MAPS for the linear conversion of raw counts to areal density in &#181;g/cm2.
Here, we demonstrate how to make use of the program, MAPS, developed by Dr. S. Vogt, to quantify data acquired from fluorescence-capable beamlines at Argonne National Laboratory (ANL) 14. The data used for the demonstration was acquired at sector 2-ID-D of ANL using the measurement setup shown in Figure 1 of 10. The fitting procedure may also be applied to data taken from other beamlines, however, note that certain characteristics of the ANL beamlines are embedded in the program and will need to be updated.

quantifying x-ray fluorescence data using maps

Quantifying X-Ray Fluorescence Data Using MAPS

The quantification of X-ray fluorescence (XRF) microscopy maps by fitting the raw spectra to a known standard is crucial for evaluating chemical composition and elemental distribution within a material. Synchrotron-based XRF has become an integral characterization technique for a variety of research topics, particularly due to its non-destructive nature and its high sensitivity. Today, synchrotrons can acquire fluorescence data at spatial resolutions well below a micron, allowing for the evaluation of compositional variations at the nanoscale. Through proper quantification, it is then possible to obtain an in-depth, high-resolution understanding of elemental segregation, stoichiometric relationships, and clustering behavior.
This article explains how to use the MAPS fitting software developed by Argonne National Laboratory for the quantification of full 2-D XRF maps. We use as an example results from a Cu(In,Ga)Se2 solar cell, taken at the Advanced Photon Source beamline 2-ID-D at Argonne National Laboratory. We show the standard procedure for fitting raw data, demonstrate how to evaluate the quality of a fit and present the typical outputs generated by the program. In addition, we discuss in this manuscript certain software limitations and offer suggestions for how to further correct the data to be numerically accurate and representative of spatially resolved, elemental concentrations.

An example of proper fitting results can be seen in the following Figures. Firstly, in Figure 1 a direct comparison is shown between a poor fit and a good fit for the integral spectrum. The bad fit is reparable by both ensuring no elements are missing, for instance copper, which has a clear peak in Figure 1(left) but is not being included in the fit, and adjusting the branching ratios of the L and K lines to improve the accuracy....

Here, we demonstrate the use of the X-ray fluorescence fitting software, MAPS, created by Argonne National Laboratory for the quantification of fluorescence microscopy data. The quantified data that results is useful for understanding the elemental distribution and stoichiometric ratios within a sample of interest.

The quantification of X-ray fluorescence (XRF) microscopy maps by fitting the raw spectra to a known standard is crucial for evaluating chemical ...

Synchrotronbased X-ray fluorescence is an important technique for observing elemental segregation, stoichiometry relationships and clustering behavior in samples from a multitude of fields including biology, chemistry and material science. The information obtained from these studies is qualitative until proper quantification procedures are used to convert raw fluorescence counts into elemental aerial masses. This video will demonstrate how to use the quantification program created by Argonne National Laboratory to generate numerical information for two-dimensional X-ray fluorescence maps.To use the MAPS program, it is first necessary to download the IDL software from the Internet. This can currently be done by going to the website for IDL and creating an account. Next, select My Account then Downloads, and it will show a page of all the available programs.Scroll down and select the most recent version of IDL. Next MAPS may be downloaded from the Argonne National Laboratory website. After downloading and extracting the zip folder, there should be four files.Compound.dat, henke. xdr, maps and xrf_library.csv. The three files other than maps should be copied and pasted in the IDL sub-

quantifying-x-ray-fluorescence-data-using-maps

Research

JoVE Journal

Chemistry

By employing a spectrally resolved two-photon microscopy imaging system, pixel-level maps of Förster Resonance Energy Transfer (FRET) efficiencies are obtained for cells expressing membrane receptors hypothesized to form homo-oligomeric complexes.  From the FRET efficiency maps, we are able to estimate stoichiometric information about the oligomer complex under study.

In vivo Quantification of G Protein Coupled Receptor Interactions using Spectrally Resolved Two-photon Microscopy

This protocol describes how to use total internal reflection fluorescence microscopy to visualize and track single receptors on the surface of living cells and thereby analyze receptor lateral mobility, size of receptor complexes as well as to visualize transient receptor-receptor interactions. This protocol can be extended to other membrane proteins.

High-resolution Spatiotemporal Analysis of Receptor Dynamics by Single-molecule Fluorescence Microscopy

We describe a non-invasive animal imaging platform that allows the detection, quantification, and monitoring of ovarian cancer growth and recurrence. This intra-peritoneal xenograft model mimics the clinical profile of patients with ovarian cancer.

Murine Model for Non-invasive Imaging to Detect and Monitor Ovarian Cancer Recurrence

Here, we present a protocol on how to determine the quantity and distribution of metals in a sample using synchrotron X-ray fluorescence. We focus on adherent cells, and describe the chemical fixation method to prepare this sample. We then describe how to mount and image the sample using synchrotron X-rays.

Preparing Adherent Cells for X-ray Fluorescence Imaging by Chemical Fixation

The use of energy dispersive X-ray tomography in the scanning transmission electron microscope to characterize elemental distributions within single nanoparticles in three dimensions is described.

Energy Dispersive X-ray Tomography for 3D Elemental Mapping of Individual Nanoparticles

We describe a procedure for the detection of chemical elements present in situ in human cells as well as their in vitro quantification. The method is well-suited to any cell type and is particularly useful for quantitative chemical analyses in single cells following in vitro metal oxide nanoparticles exposure.

In Situ Detection and Single Cell Quantification of Metal Oxide Nanoparticles Using Nuclear Microprobe Analysis

This paper describes a protocol to achieve 3D chemical maps combining energy filtered imaging and electron tomography. The chemical distribution of two catalyst supports formed by elements that are difficult to distinguish by other imaging techniques was studied. Each application consists of mapping overlapped chemical elements - respectively spaced-ionization edges.

Obtaining 3D Chemical Maps by Energy Filtered Transmission Electron Microscopy Tomography

Here, we present a protocol for typical experiments of soft X-ray absorption spectroscopy (sXAS) and resonant inelastic X-ray scattering (RIXS) with applications in battery material studies.

Elemental-sensitive Detection of the Chemistry in Batteries through Soft X-ray Absorption Spectroscopy and Resonant Inelastic X-ray Scattering

We describe a beamline setup meant to carry out rapid two-dimensional x-ray fluorescence and x-ray microdiffraction mapping of single crystal or powder samples using either Laue (polychromatic radiation) or powder (monochromatic radiation) diffraction. The resulting maps give information about strain, orientation, phase distribution, and plastic deformation.

Synchrotron X-ray Microdiffraction and Fluorescence Imaging of Mineral and Rock Samples

Here, we present a protocol for high-resolution optical detection of chemical information around implanted medical devices with X-ray excited luminescence chemical imaging (XELCI). This novel imaging technique is developed in our lab which enables studying implant-associated infection biochemistry.

High Spatial Resolution Chemical Imaging of Implant-Associated Infections with X-ray Excited Luminescence Chemical Imaging Through Tissue

Poznaj metodę kwantyfikacji danych fluorescencji rentgenowskiej za pomocą oprogramowania MAPS. Technika ta umożliwia analizę rozkładu pierwiastków i stosunków stechiometrycznych w próbkach biologicznych i materiałowych.

Quantifying X-Ray Fluorescence Data Using MAPS

Przeglądaj więcej filmów